Unbricking Samsung Galaxy Note GT-N7000 With Easy Jtag Box

Unbricking Samsung Galaxy Note GT-N7000

Unbricking / Boot repair Samsung Galaxy Note GT-N7000 is easy, but you should disassembling the phone.

Symptoms : 

• Phone's dead or black screen
• Can't charging
• Can't entering download mode or recovery mode

Causes : 

• Upgrade firmware process fault
• Rooting
• Flashing with wrong firmware
• Other software process fault

Tool & Materials :

• Easy Jtag box
• Disassembly tool
• Soldering tool
• PC 

Step by step :

• Connect Easy Jtag box to PC
• Open Easy Jtag software
• Browse and select N7000 repair file
• Click Show pinout
• Disassembly phone
• Solder JTAG cable to phone JTAG pad / pinout, GND, NRST, TDO, RTCK, TCK, TMS, TDI and TRST pin. JTAG pinout are very small; professional experience in soldering is required to connect wires to the JTAG interface.
• Insert battery or power suply and connect USB cable to phone, in some case, you need to hold power on button while resurrection process.

• Click Run Easy Repair
• Resurrection processing and wait untill done and you will get this log below if resurrection is done

EasyJtag Suite ver.: 1.0.56.5 started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
Successefuly connected to box on COM395
Box S/N: xxxxxxxxxx, ,FW Ver.: 01.47
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA48-927D
Z3X Card Version : 22
Z3X Card Activation [JTAG] : 1
Resources ver. : MainRC ver.OCD040Z001 (C)2012 z3x-team.com
Loading repair file: 'C:\Program Files\Z3X\EASYJTAG\Repair Files\Samsung GT-N7000_V1.01.rcp'
Repair File ver. : Easy Repair for Mfg: SAMSUNG Model: GT-N7000, Ver.: 1.01
Error loading information!
Easy-Repair file load OK!
Using EasyRepair Mode...
Checking repair data...
EasyJtag Suite ver.: 1.0.56.5 started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
For support and updates visit http://easy-jtag.com
Initialising: SAMSUNG GT-N7000 Config ver.:1.01
I/O Level set to : 2800 mV
Box S/N: xxxxxxxxxxxx ,FW Ver.: 01.47
Connecting to Target...
JTAG device: S5PC210
CPU IDCODE : 0x4BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x4
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A9
Halting CPU...
Init target ...
Starting target communication...
Detecting emmc memory parameters of bank (0) ...
EMMC #0 : ID : 0x00010015 Name : VYL00M Size : 16 GB
EMMC #1 : ID : 0x00010015 Name : VYL00M Size : 524 kB
eMMC flash device(s) found, Device ID : 0x00150001
NAND Writing GPT...
eMMC Write OK! Elapsed time: 37.123123s (110.336 KiB/s)
NAND Writing SBL1...
eMMC Write OK! Elapsed time: 21.015202s (60.908 KiB/s)
NAND Writing SBL2...
eMMC Write OK! Elapsed time: 20.642179s (62.009 KiB/s)
NAND Writing PARAM...
eMMC Write OK! Elapsed time: 75.368309s (108.693 KiB/s)
NAND Writing ROM2...
eMMC Write OK! Elapsed time: 70.836052s (7.228 KiB/s)
All Done.

•  De-solder JTAG wires

Now phone is in bootable conditions, and still need flashing Stock ROM via Odin.  To put into download mode, press & hold Volume Down (-)  +  Home button and then power on the phone, press volume up (+) to confirm.

Posted in: Easy Jtag, Samsung JTAG Log